Chemical

No.18 Light source for thin-layer chromatography

[ Problem Point ] A low-cost, easy-to-use analytical method was needed. [ ⇒Kaizen Point ] It was used for pharmaceutical purity tests and follow-up confirmation tests for synthetic experiments. Fluoresces green under UV irradiation at 254 nm For detection by ...

Read More »

No.5 Drying the epoxy resin

[ Problem Point ] There was no heater controller that could heat intermittently Even when there was no work, the heater was operating and power was wasted. Also, when the line stopped, cracks occurred in the dry part. And when ...

Read More »

No.4 Heating of rubber molded products

[ Problem Point ] There was no heater controller that could heat intermittently Even when there was no work, the heater was operating and power was wasted. Also, when the line stopped, the heated part became defective. And when it ...

Read More »

No.3 Preheating rubber molded products

[ Problem Point ] When the line stopped, the heated part became defective. And when it was restarted, there were cases where unprocessed products were generated due to forgetting to turn on the switch. Also, even when there was no ...

Read More »

No.2 Drying of resin pellets

[ Problem Point ] When the line stopped, the heated part was fused. And when I restarted, there were cases where water droplets remained due to forgetting to turn on the switch. [ ⇒Kaizen Point ] Using a speed proportional ...

Read More »

No.1 Heating of resin sheet

[ Problem Point ] When the line stopped, the heated part became defective. And when it was restarted, there were cases where unprocessed products were generated due to forgetting to turn on the switch. [ ⇒Kaizen Point ] Using the ...

Read More »

No.60 Chemical liquid heater

[ Problem Point ] There was no good heater that could heat the chemical liquid at high speed. [ ⇒Kaizen Point ] Three halogen line heaters were combined to create a triangular space, and a quartz tube was passed through. ...

Read More »

No.19 Cooling film cutting blade

《Problem Point 》 The resin was fused to the cutting blade due to frictional heat, which was a problem. 《⇒Kaizen Point 》 An Air Blow Cooler was used. The MTBF was improved because the resin did not adhere.

Read More »

No.18 Cooling during film fusion sealing

《Problem Point 》 When the film was fused, it was sometimes peeled off due to residual heat. 《⇒Kaizen Point 》 An Air Blow Cooler was used. After thermocompression bonding, it was cooled by removing heat with a Air Blow Cooler. ...

Read More »

No.12 Reproduction of thermal distortion

《Problem Point 》 There was no good equipment to pinpoint the sample to a low temperature. 《⇒Kaizen Point 》 An Air Blow Cooler was used. Pinpoint cooling is possible with the needle nozzle. Since the set temperature can be maintained ...

Read More »

No.10 Electron microscope sample cooling

《Problem Point 》 There was no good equipment to pinpoint the sample to a low temperature. 《⇒Kaizen Point 》 An Air Blow Cooler was used. Pinpoint cooling is possible with the needle nozzle. Since the set temperature can be maintained ...

Read More »

No.9 Refrigerant of Liebig condenser

《Problem Point 》 It was an environment where cooling water could not be used. 《⇒Kaizen Point 》 An Air Blow Cooler was used. With the combination of electricity and air, the water supply and drainage system could be omitted. Since ...

Read More »

No.8 Refrigerant of Dewar condenser

《Problem Point 》 It was an environment where cooling water could not be used. 《⇒Kaizen Point 》 An Air Blow Cooler was used. With the combination of electricity and air, the water supply and drainage system could be omitted. Since ...

Read More »

No.7 Refrigerant of Dimroth condenser

《Problem Point 》 It was an environment where cooling water could not be used. 《⇒Kaizen Point 》 An Air Blow Cooler was used. With the combination of electricity and air, the water supply and drainage system could be omitted. Since ...

Read More »

No.6 Refrigerant of Allihn condenser

《Problem Point 》 It was an environment where cooling water could not be used. 《⇒Kaizen Point 》 An Air Blow Cooler was used. With the combination of electricity and air, the water supply and drainage system could be omitted. Since ...

Read More »