Machine

No.13 Tensile tester low temperature setting

《Problem Point 》 There was no good equipment to pinpoint the sample to a low temperature. 《⇒Kaizen Point 》 An Air Blow Cooler was used. Pinpoint cooling is possible with the needle nozzle. Since the set temperature can be maintained ...

Read More »

No.40 Soldering of tip saw

[ Problem Point ] There was no easy way to set the tip of the tip saw to 1000℃ [ ⇒Kaizen Point ] It was heated to a high temperature using a halogen point heater. Since it can be processed ...

Read More »

No.1 Pinpoint heating of resin

[ Problem Point ] There was no compact heater of far infrared which can pinpoint point the resin. [ ⇒Kaizen Point ] Heated using a far infrared ray point heater FPH-30. The welding of the resin got to work gently.

Read More »

No.51 Heating and drying of the sealer

Heating and drying of the sealer

[ Problem Point ] It is necessary to shorten the drying time of the sealer. [ ⇒Kaizen Point ] We were using the line condensing type halogen line heater. Because the line condensing type, in accordance with the application position ...

Read More »

No.50 Drying after car wash

No.50 Drying after car wash

[ Problem Point ] It is necessary to reduce the draining drying time. [ ⇒Kaizen Point ] We were using the parallel light type halogen line heater. Because the light heating, non-contact heating is possible, it was able to shorten ...

Read More »

No.34 Borosilicate glass tube melting

No.34 Borosilicate glass tube melting

[ Problem Point ] There was no substitute heat source to replace gas. [ ⇒Kaizen Point ] Borosilicate glass tube was melted using a halogen point heater. The glass tube processing process was composed only by electric equipment. In addition, ...

Read More »

No.105 Shrink fitting of a small cylinder

No.105 Shrink fitting of a small cylinder

[ Problem Point ] Heating equipment that can be used in online was necessary. [ ⇒Kaizen Point ] We ware shrink-fitted by using the Air Blow Heater. The start of the line become faster. Installation because it does not use ...

Read More »

No.28 Infrared heat caulking of resin boss

No.28 Infrared heat caulking of resin boss

[ Problem Point ] Resin adheres to the punch, and this has been a cause of the processing failure. [ ⇒Kaizen Point ] We use tha halogen point heater heating the resin boss. Problem is solved because construction methods that ...

Read More »

No.95 Hot air shot peening

[ Problem Point ] In order to thicken a metallic thin film, the high temperature hot wind was required. [ ⇒Kaizen Point ] The shot-peened under high temperature conditions using the Air Blow Heater. Junction went well even if thickening ...

Read More »

No.90 Heat test of bearing

[ Problem Point ] Managing the heat-resistant temperature of grease, it came to carry out a quality assessment and there was nothing. [ ⇒Kaizen Point ] It heated from room temperature to 550℃ with the Air blow heater. The quality ...

Read More »

No.15 Heating of the LCD cover glass

[ Problem Point ] Rubber was not drying, and it was troubled by the temperature close to the sub-zero winter. [ ⇒Kaizen Point ] It was heated by the far-infrared heater which temperature rise of the high speed. Rise time ...

Read More »

No.88 Thermal caulking of resin parts

[ Problem Point ] There was no non-contact heater that can be accurately temperature control. [ ⇒Kaizen Point ] We were heated in the Air Blow Heater. In the hot air that was temperature-controlled exactly, we were able to be ...

Read More »

No.17 Brazing of Mini Valve

[ Problem Point ] We have no idea  about good way to brazing in the no-oxygen. [ ⇒Kaizen Point ] It was brazed with a small Halogen Point Heater. Junction quality is improved.

Read More »