Best Applications List

[ Problem Point ] There is no good method of carrying out circular high temperature heating. and We were in trouble. [ ⇒Kaizen Point ] The halogen ring heater with a ring hood was used. It was smoothly heated in ...

[ Problem Point ] There is no better way to heat evenly from the periphery. and We were in trouble. [ ⇒Kaizen Point ] The halogen ring heater with a ring hood was used. It was fitted to the expansion ...

[ Problem Point ] There is no better way to heat evenly from the periphery. and We were in trouble. [ ⇒Kaizen Point ] The halogen ring heater with a ring hood was used. From the feed port, it is ...

[ Problem Point ] There is no high speed heater of the corresponding to an index table, and We were in trouble. [ ⇒Kaizen Point ] Using a halogen ring heater with a reflector. Since the standup was speedy, the ...

[ Problem Point ] There is no good way to small and wide heating and We were in trouble. [ ⇒Kaizen Point ] The ring heater which can carry out wide heating of the wide area was introduced. The efficiency ...

[ Problem Point ] There is no good way to small and uniform heating and We were in trouble. [ ⇒Kaizen Point ] The ring heater which can carry out homogeneous heating of the wide area was introduced. The efficiency ...

[ Problem Point ] There is no good method of observing the process of heating. and We were in trouble. [ ⇒Kaizen Point ] The halogen ring heater with a ring hood was used. Since the test piece inserted from ...

[ Problem Point ] There is no good method of heat the small printed circuit board and We were in trouble. [ ⇒Kaizen Point ] The ring heater which can carry out uniform heating of the wide area was introduced. ...

[ Problem Point ] There is no good method of heating from all direction. and We were in trouble. [ ⇒Kaizen Point ] Shrinking heating was carried out with the halogen ring heater. Since it heated from all the circumferences, ...

[ Problem Point ] Temperature control was difficult because it was heating with warm water. [ ⇒Kaizen Point ]  The alloy heated by the Air Blow Heater. since it heated at an exact temperature of a unit once, reproducibility of ...

[ Problem Point ] Because the fuel is wet, we were in trouble without good source of ignition. [ ⇒Kaizen Point ]  Output the high temperature air blow in the Air Blow Heater, was heated and dried. Since fresh air ...

[ Problem Point ] When winter came, it was troubled without the waterdrop after car washing getting dry. [ ⇒Kaizen Point ] Drained and dried with the Air Blow Heater.

[ Problem Point ] Although the drier for industry was used for the robot, having attached it, broke down immediately and we were troubled. [ ⇒Kaizen Point ] The burr was melted with the Air Blow Heater. Since discharge temperature ...

[ Problem Point ] There was no good thing can be transparent while keeping the high-temperature heating the glass tube. [ ⇒Kaizen Point ] Were tested while raising the temperature up to 1000 ℃ in the Air Blow Heater Accuracy ...

[ Problem Point ] The wire did not fit, it was troubled by the temperature near the freezing point of winter. [ ⇒Kaizen Point ] It warmed by the Super Infrared Heater of temperature up at the moment. The wire ...

[ Problem Point ] The performance of the battery did not come out but it was troubled by the temperature near the freezing point of winter. [ ⇒Kaizen Point ] It warmed by the Super Infrared Heater of temperature up ...

[ Problem Point ] There was omitted thermal diffusion test by air. [ ⇒Kaizen Point ] The diffusion test was done,the amount control of winds in increments of 1liter unit raising temperature in increments of 1 degree unit with a ...

[ Problem Point ] The marks of water drop remained and were worrisome when natural drying was carried out. [ ⇒Kaizen Point ] Nitrogen was heated with the Air Blow Heater and it dried. The marks of water drop were ...

[ Problem Point ] When processing the wire produced by powder metallurgy,it had trouble to cracking or cutting. [ ⇒Kaizen Point ] So brittle,while heating to the processing 400 ℃ – 700 ℃ by the Air Blow Heater. The quality ...

[ Problem Point ] It wasn’t possible to make hot argon gas while keeping the purity. [ ⇒Kaizen Point ] Argon gas was heated by the Air Blow Heater. Air did not mix and the high temperature gas of 550℃ ...

[ Problem Point ] We have no idea about how to no-contact heating in line. [ ⇒Kaizen Point ] The high temperature air of the suitable temperature was made with the Air Blow Hater and it projected. It came to ...

[ Problem Point ] We have no idea about how to heating and cooling at the same time in line. [ ⇒Kaizen Point ] It made high fever air of a suitable temperature with the Air Blow Heater, projected and ...

[ Problem Point ] It was in trouble because the temperature of steam of the tunnel type steam-oven was not able to be adjusted. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to ...

[ Problem Point ] It was in trouble because the heat resistant of the polyethylene is low. [ ⇒Kaizen Point ] The temperature of air of the heating sterilization furnace has been adjusted with the Air Blow Heater. Possible to ...

[ Problem Point ] There was distance from a boiler,it was in trouble because the temperature of the steam fell. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to make overheating saturated steam ...