Assembly

[ Problem Point ] There was distance from a boiler,it was in trouble because the temperature of the steam fell. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to make overheating saturated steam ...

[ Problem Point ] It was in trouble because the priority oxidation of the tin occurred. [ ⇒Kaizen Point ] The soldering iron shielded with the nitrogen gas was made. The priority oxidation of tin is suppressed to solder in ...

[ Problem Point ] It was in trouble because the temperature of the boiler steam didn’t rise. [ ⇒Kaizen Point ] Steam was heated by the Air Blow Heater. Wet steam became dry steam.

[ Problem Point ] There were no tools in which small high-temperature tunnel furnace heat source,  and We were in trouble. [ ⇒Kaizen Point ] In a large the high-temperature heating with the Air Blow Heater capacity. Since raising the ...

[ Problem Point ] There were no tools in which no fast way of drying the metal parts,  and We were in trouble. [ ⇒Kaizen Point ] In a large the high-temperature heating with the Air Blow Heater capacity. Work in ...

[ Problem Point ]   There were no tools in which optimum temperature for heating the moving part,  and We were in trouble. [ ⇒Kaizen Point ] Heated in the Air Blow Heater. Mobility could be maintained without contact can ...

[ Problem Point ] There were no tools in which quickly dry water-based paint,  and We were in trouble. [ ⇒Kaizen Point ] In a large Air Blow Heater the blower at high temperature. Faster drying, increased production.

[ Problem Point ] The rapid heating is not possible to the chamber, had trouble. [ ⇒Kaizen Point ] In a large the Air Blow Heater warmed rapidly. The rise of the processing cycle time, significantly increasing the number of ...

[ Problem Point ] It was in trouble because Flushing cleaning solution after plumbing processing was left. [ ⇒Kaizen Point ] Rust did not go out because it had dried remaining water by the Air Blow Heater.

[ Problem Point ] When cleaning after cutting chips, water drops were still in trouble. [ ⇒Kaizen Point ] The Air Blow Heater,attached to the needle nozzle,dry blower. Because the hot air blower hot moment, better drying.

[ Problem Point ] When the adhesive film and paper,air bubbles were made trouble. [ ⇒Kaizen Point ] Wide nozzle attached to the preheated the Air Blow Heater. To improve the adhesion of air bubbles disappeared.

[ Problem Point ] It’s being checked by the tester just after the production of electronic components. Control of the heat cycle was difficult. [ ⇒Kaizen Point ] Aging was done with a wide nozzle of the Air Blow Heater. ...

[ Problem Point ] Laboratory has been electrified,the gas was not able to be used and I was in trouble. [ ⇒Kaizen Point ] It was heated by the Air Blow Heater. It was very useful for high temperature heating ...

[ Problem Point ] Had trouble peeling off the seal is broken at the end. [ ⇒Kaizen Point ] A spot was heated by the Air Blow Heater and the glue was made soft. The productivity came off well,and improved.

[ Problem Point ] Gluing of lead free solder would be a problem badly. [ ⇒Kaizen Point ] The small spot was preheated by the Air Blow Heater. After preheating, gluing of solder became good. Moreover it was also heat ...

[ Problem Point ] We have no idea about good annealing of the glass. [ ⇒Kaizen Point ] Warming by the Ir Panel Heater. Glass is able to be warmed on the broad wavelength.

[ Problem Point ] When resin board was processed while getting cold,breakage entered. [ ⇒Kaizen Point ] Resin board was preheated by the Air Blow Heater. The flexibility was recovered and breakage was prevented.

[ Problem Point ] It wasn’t possible to make hot nitrogen gas while keeping the purity. [ ⇒Kaizen Point ] Nitrogen was heated by the Air Blow Heater. Air didn’t get mixed and it was possible to make high temperature ...

[ Problem Point ] Wrinkles of shrink films of DVD packing were left,and we were in trouble. [ ⇒Kaizen Point ] It was heated by a slight fever by the Air Blow Heater and wrinkles were flatted. The quality of ...

[ Problem Point ] We have no idea  about heating unit for drying booth. [ ⇒Kaizen Point ] Drying by the Ir Panel Heater. Since rapid heat up on drying booth,increased uptime. Now able to respond flexibly to unexpected interrupt ...

[ Problem Point ] We have no idea  about curing of the epoxy resin. [ ⇒Kaizen Point ] Curing by the Ir Panel Heater. Since rapid curing, increased uptime. Now able to respond flexibly to unexpected interrupt work.

[ Problem Point ] We were in trouble because there were no small ignition sources. [ ⇒Kaizen Point ] The Air Blow Heater ignited heated to high temperature.

[ Problem Point ] We have no idea  about Reflow of printed circuit boards. [ ⇒Kaizen Point ] Reflow by the Ir Panel Heater. Since rapid heating, increased uptime. Now able to respond flexibly to unexpected interrupt work.

[ Problem Point ] Starting of a drier took time too much. [ ⇒Kaizen Point ] Dried by the Ir Panel Heater. Since the dryer is heated quickly, no longer waiting time. Now able to respond flexibly to unexpected interrupt ...

[ Problem Point ] A few bruises were the claim, and we were in trouble. [ ⇒Kaizen Point ] It was heated lightly by the Air Blow Heater,and the luster of the surface was taken good.