Machine

[ Problem Point ] After washing the remaining pickling was in trouble. [ ⇒Kaizen Point ] The Air Blow Heater,it flew in the residual water and heat the air blow was coming out of rust.

[ Problem Point ] We were bagged and dried groceries. But there was trouble grows mold. [ ⇒Kaizen Point ] It dried heating nitrogen by the Air Blow Heater. Because nitrogen did not contain water vapor. It became the anti-mold ...

[ Problem Point ] It was in trouble because Flushing cleaning solution after plumbing processing was left. [ ⇒Kaizen Point ] Rust did not go out because it had dried remaining water by the Air Blow Heater.

[ Problem Point ] When cleaning after cutting chips, water drops were still in trouble. [ ⇒Kaizen Point ] The Air Blow Heater,attached to the needle nozzle,dry blower. Because the hot air blower hot moment, better drying.

[ Problem Point ] When the adhesive film and paper,air bubbles were made trouble. [ ⇒Kaizen Point ] Wide nozzle attached to the preheated the Air Blow Heater. To improve the adhesion of air bubbles disappeared.

[ Problem Point ] It’s being checked by the tester just after the production of electronic components. Control of the heat cycle was difficult. [ ⇒Kaizen Point ] Aging was done with a wide nozzle of the Air Blow Heater. ...

[ Problem Point ] Heat ran away from the furnace,was the problem of quenching quality. [ ⇒Kaizen Point ] The furnace was air sealed with the Air Blow Heater. The temperature of the interior was kept,and the quality of quenching ...

[ Problem Point ] Laboratory has been electrified,the gas was not able to be used and I was in trouble. [ ⇒Kaizen Point ] It was heated by the Air Blow Heater. It was very useful for high temperature heating ...

[ Problem Point ] The control of the surface tension of a metallic film was difficult when drying with the high temperature gas. [ ⇒Kaizen Point ] It dried using a wide nozzle by the Air Blow Heater. The surface ...

[ Problem Point ] We have no way to the drawing press wrinkle. [ ⇒Kaizen Point ] Preheated metal material by the Halogen Line Heater. Since the maximum temperature heated up in 5sec, immediately after the start of operation could ...

[ Problem Point ] We have trouble to the die temperature drift for changes in precision finishing. [ ⇒Kaizen Point ] Preheated die by the Halogen Line Heater. Since the maximum temperature heated up in 5sec, immediately after the start ...

[ Problem Point ] We used the industry dryer. Unable to fine temperature control was a problem. [ ⇒Kaizen Point ] Heated and dried in large type the Air Blow Heater. Dehumidification and sufficient quality of injection molded raised in ...

[ Problem Point ] It is very difficult to annealing temperature control. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater casting surface. Since the maximum temperature heated up in 5sec, immediately after the start of operation could work.The ...

[ Problem Point ] We have no idea about good annealing of the glass. [ ⇒Kaizen Point ] Warming by the Ir Panel Heater. Glass is able to be warmed on the broad wavelength.

[ Problem Point ] It wasn’t possible to make hot nitrogen gas while keeping the purity. [ ⇒Kaizen Point ] Nitrogen was heated by the Air Blow Heater. Air didn’t get mixed and it was possible to make high temperature ...

[ Problem Point ] We have no idea  about heating unit for drying booth. [ ⇒Kaizen Point ] Drying by the Ir Panel Heater. Since rapid heat up on drying booth,increased uptime. Now able to respond flexibly to unexpected interrupt ...

[ Problem Point ] We have no idea  about curing of the epoxy resin. [ ⇒Kaizen Point ] Curing by the Ir Panel Heater. Since rapid curing, increased uptime. Now able to respond flexibly to unexpected interrupt work.

[ Problem Point ] We were in trouble because there were no small ignition sources. [ ⇒Kaizen Point ] The Air Blow Heater ignited heated to high temperature.

[ Problem Point ] A few bruises were the claim, and we were in trouble. [ ⇒Kaizen Point ] It was heated lightly by the Air Blow Heater,and the luster of the surface was taken good.

[ Problem Point ] We were in trouble because there were no deburring methods of a resin mold. [ ⇒Kaizen Point ] An abuse moth just applied hot air lightly by the Air Blow Heater, and went off easily. Yield ...

[ Problem Point ] It was no easy way to trouble-free welding without oxygen. [ ⇒Kaizen Point ] Welded by the small point halogen heater. Easily welded in nitrogen atmosphere. Junction with improved quality.

[ Problem Point ] There was no heater can heat to penetrate the polymer film on the upper side metallic mold. [ ⇒Kaizen Point ] We use the Halogen Point Heater Because the halogen point was heated to pinpoint the ...

[ Problem Point ] The crack happened and very troubled. [ ⇒Kaizen Point ] The pipe preheated with the Halogen Point Heater. The surface tensity was removed because it heated at the suitable temperature and the crack disappeared.

[ Problem Point ] We were in trouble because there was no space where BLOWER which transfers cooling water after the back weld pulled out is installed. [ ⇒Kaizen Point ] It was dried at high temperature by the Power  ...

[ Problem Point ] The hole crack happened and very troubled. [ ⇒Kaizen Point ] The pipe preheated with the Halogen Point Heater. The surface tensity was removed because it heated at the suitable temperature and the crack disappeared.