[ Problem Point ] Write notes to the sample in the test, It was in trouble if there is no heat resistance on scratch paper. [ Kaizen Point ] Use the ToughTape, wrote a memo in magic from above. Notes ...
Read More »No.16 Attachment of a film (mask) at the time of exposure and printing.
[ Problem Point ] In order that there might not be heat resistance and radiation resistance in a mask stop tape, when it exposed several times, distortion arose. [ Kaizen Point ] The mask stop was carried out on the ...
Read More »No.15 Insulation protects the hard disk
[ Problem Point ] The insulation for protecting from the mistake touch under assembly is required. [ Kaizen Point ] Insulated protection was carried out on the Toughtape. Reliability improved by the sufficient insulation and radiation resistance of PEEK resin.
Read More »No.14 Motor and Transformer interlayer insulation
[ Problem Point ] A pole crosses between the commutator fragment of rotter, time, it was in trouble about degradation early stage of a interlayer insulation thing by impulse wave discharge. [ Kaizen Point ] Insulated protection was carried out ...
Read More »No.13 Flow and reflow soldering process for printed circuit board, masking the Gold Plate Contact
[ Problem Point ] Heat resistance is required to protect a golden terminal from cream solder. [ Kaizen Point ] The Toughtape was used and masked. It is improvement in reliability at sufficient heat resistance.
Read More »No.12 Solidarity and splices that require tensile bond strength
[ Problem Point ] Degradation would be a problem early for a high fever near the engine. [ Kaizen Point ] It banded together using the Toughtape corresponding to 260 ℃ of high fever. Since after heating has stable adhesive ...
Read More »No.11 Temporary fixing of aging heat and cycle test examination process
[ Problem Point ] The inside of a constant temperature bath cannot perform a temporary attachment in a high fever. [ Kaizen Point ] The temporary attached by the Toughtape. Work became easy and working efficiency increased.
Read More »No.10 Outer stop winding and interlayer insulating transformers and coils
[ Problem Point ] The quality of an insulator needs to be inserted because of rare short prevention. [ Kaizen Point ] Insulated protection was carried out on the Toughtape. Reliability improved by sufficient insulation and radiation resistance.
Read More »No.9 Attachment of in-company Kamban of a heat-resistant board
[ Problem Point ] High fever immediately after production, Kanban can not be pasted. [ Kaizen Point ] Kanban is pasted on Toughtape. Kanban production system expression fill the gap.
Read More »No.8 Temporarily sealing of steam sterilization
[ Problem Point ] A weather strip did not go well, but water infiltrated into sterilizing an instrument in steam. [ Kaizen Point ] That the seal-up in Toughtape. A weather strip did not go well, but water infiltrated into ...
Read More »No.7 Fixed position of the exposure apparatus
[ Problem Point ] The position shifted and it was troubled by the exposure examination. [ Kaizen Point ] The temporary attached by the Toughtape. The shape is strong in 260 ℃ of permanent heat-resistance and radiation, and stable, so ...
Read More »No.6 Temporary fixing of boiler construction
[ Problem Point ] Instrument could not be fixed temporarily during construction of the boiler [ Kaizen Point ] The temporary attached by the Toughtape. Because the shape is stable and resistant to heat and humidity of a permanent 260 ...
Read More »No.5 Scald the vial
[ Problem Point ] I was in trouble because it wasn’t possible to stand outside the Viola bottle against not to cork and to boil. [ Kaizen Point ] Bundle with the Toughtape. Because the shape is stable and resistant ...
Read More »No.4 End stop of a solar panel
[ Problem Point ] It takes time before glue dries. [ Kaizen Point ] The solar panel was stopped on the frame on the Toughtape. Since the lasting heat resistance of 260 ℃ and form are stable, fixation is possible ...
Read More »No.3 End stop before heat shrinking of cloth
[ Problem Point ] For lack of heat resistance, splice unsuccessful. [ Kaizen Point ] It was spliced using the Toughtape.The shape was stable by 260 ℃ of resistance to distortion at high temperatures, so splice work became smooth, and ...
Read More »No.2 End surface of the film take-up fixed
[ Problem Point ] The end stop tape dissolved for thermal storage of a film, and poor adherence occurred for the product. [ Kaizen Point ] The end stop was carried out on the Toughtape. Since form was stable in ...
Read More »No.1 Splicing and connecting the film
[ Problem Point ] For lack of heat resistance, splice unsuccessful. [ Kaizen Point ] It was spliced using the Toughtape. The shape was stable by 260 ℃ of resistance to distortion at high temperatures, so splice work became smooth, ...
Read More »Toughtape Price List
D/# Unit Price US$ TM-HT-25 1 unit 1 piece US$100 TM-HT-25 1 unit 10 piece US$900 Request for quotation
Read More »PEEK “Tough tape”
Heat resisting tape with plastic protective PEEK “Toughtape” “Toughtape” is heat-resistant insulating tape protects the world’s first with PEEK resin. It was developed for cylindrical lithium-ion battery protection tab 18650. It could be commercialized successfully developed to withstand high temperature ...
Read More »PEEK “Tough tape” products
<< products >> PEEK “Tough tape” PEEK “Tough tape” price list Best Applications List of PEEK “Tough tape” Splicing and connecting the film End surface of the film take-up fixed End stop before heat shrinking of cloth End stop ...
Read More »