Air Blow Heater Best Applications List

[ Problem Point ] Could not be heated the dummy gas to evaluate the performance of the catalyst. [ ⇒Kaizen Point ] The double glazing tube specification DGH type for medicine-proof of the Air Blow Heater was used, and it ...

[ Problem Point ] There was no non-contact heater that can be accurately temperature control. [ ⇒Kaizen Point ] We were heated in the Air Blow Heater. In the hot air that was temperature-controlled exactly, we were able to be ...

[ Problem Point ] There was no small the Air Blow Heater which can heat a little inspection gas. [ ⇒Kaizen Point ] We were heated in the breeze by the Air Blow Heater ABH100v-50w/10PS. Since inspection gas was preheated ...

[ Problem Point ] There was no the Air Blow Heater hat can heat a small amount of shielding gas. [ ⇒Kaizen Point ] We were heated in the breeze by the Air Blow Heater ABH100v-50w/10PS. It can be pre-heated ...

[ Problem Point ] There was no the Air Blow Heater that can be heated in a nitrogen breeze. [ ⇒Kaizen Point ] We were heated in the breeze by the Air Blow Heater ABH100v-50w/10PS. It is possible to heat ...

[ Problem Point ] Temperature control was difficult because it was heating with warm water. [ ⇒Kaizen Point ]  The alloy heated by the Air Blow Heater. since it heated at an exact temperature of a unit once, reproducibility of ...

[ Problem Point ] Because the fuel is wet, we were in trouble without good source of ignition. [ ⇒Kaizen Point ]  Output the high temperature air blow in the Air Blow Heater, was heated and dried. Since fresh air ...

[ Problem Point ] When winter came, it was troubled without the waterdrop after car washing getting dry. [ ⇒Kaizen Point ] Drained and dried with the Air Blow Heater.

[ Problem Point ] Although the drier for industry was used for the robot, having attached it, broke down immediately and we were troubled. [ ⇒Kaizen Point ] The burr was melted with the Air Blow Heater. Since discharge temperature ...

[ Problem Point ] There was no good thing can be transparent while keeping the high-temperature heating the glass tube. [ ⇒Kaizen Point ] Were tested while raising the temperature up to 1000 ℃ in the Air Blow Heater Accuracy ...

[ Problem Point ] There was omitted thermal diffusion test by air. [ ⇒Kaizen Point ] The diffusion test was done,the amount control of winds in increments of 1liter unit raising temperature in increments of 1 degree unit with a ...

[ Problem Point ] The marks of water drop remained and were worrisome when natural drying was carried out. [ ⇒Kaizen Point ] Nitrogen was heated with the Air Blow Heater and it dried. The marks of water drop were ...

[ Problem Point ] When processing the wire produced by powder metallurgy,it had trouble to cracking or cutting. [ ⇒Kaizen Point ] So brittle,while heating to the processing 400 ℃ – 700 ℃ by the Air Blow Heater. The quality ...

[ Problem Point ] It wasn’t possible to make hot argon gas while keeping the purity. [ ⇒Kaizen Point ] Argon gas was heated by the Air Blow Heater. Air did not mix and the high temperature gas of 550℃ ...

[ Problem Point ] We have no idea about how to no-contact heating in line. [ ⇒Kaizen Point ] The high temperature air of the suitable temperature was made with the Air Blow Hater and it projected. It came to ...

[ Problem Point ] We have no idea about how to heating and cooling at the same time in line. [ ⇒Kaizen Point ] It made high fever air of a suitable temperature with the Air Blow Heater, projected and ...

[ Problem Point ] It was in trouble because the temperature of steam of the tunnel type steam-oven was not able to be adjusted. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to ...

[ Problem Point ] It was in trouble because the heat resistant of the polyethylene is low. [ ⇒Kaizen Point ] The temperature of air of the heating sterilization furnace has been adjusted with the Air Blow Heater. Possible to ...

[ Problem Point ] There was distance from a boiler,it was in trouble because the temperature of the steam fell. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to make overheating saturated steam ...

[ Problem Point ] It was in trouble because the priority oxidation of the tin occurred. [ ⇒Kaizen Point ] The soldering iron shielded with the nitrogen gas was made. The priority oxidation of tin is suppressed to solder in ...

[ Problem Point ] It was in trouble because the surface of the tart burned. [ ⇒Kaizen Point ] The surface was warmed over by the Air Blow Heater. The temperature was able to be adjusted, the combustion color was ...

[ Problem Point ] It was in trouble because the temperature of the boiler steam didn’t rise. [ ⇒Kaizen Point ] Steam was heated by the Air Blow Heater. Wet steam became dry steam.

[ Problem Point ] We have no idea to concentrate without oxygen. [ ⇒Kaizen Point ] Nitrogen gas was blown into a sample directly and it was concentrated. The volatile low solvent like DMSO and water could also be concentrated ...

[ Problem Point ] We have no idea about Silicon wafer easy heating. [ ⇒Kaizen Point ] The high temperature Nitrogen gas was injected with the Air Blow Heater, and the top surface temperature was adjusted to 40O℃. The Silicon ...

[ Problem Point ] There were no tools in which small high-temperature tunnel furnace heat source,  and We were in trouble. [ ⇒Kaizen Point ] In a large the high-temperature heating with the Air Blow Heater capacity. Since raising the ...