[ Problem Point ] After washing the remaining pickling was in trouble. [ ⇒Kaizen Point ] The Air Blow Heater,it flew in the residual water and heat the air blow was coming out of rust.

[ Problem Point ] We were bagged and dried groceries. But there was trouble grows mold. [ ⇒Kaizen Point ] It dried heating nitrogen by the Air Blow Heater. Because nitrogen did not contain water vapor. It became the anti-mold ...

[ Problem Point ] It was in trouble because Flushing cleaning solution after plumbing processing was left. [ ⇒Kaizen Point ] Rust did not go out because it had dried remaining water by the Air Blow Heater.

[ Problem Point ] When cleaning after cutting chips, water drops were still in trouble. [ ⇒Kaizen Point ] The Air Blow Heater,attached to the needle nozzle,dry blower. Because the hot air blower hot moment, better drying.

[ Problem Point ] When the adhesive film and paper,air bubbles were made trouble. [ ⇒Kaizen Point ] Wide nozzle attached to the preheated the Air Blow Heater. To improve the adhesion of air bubbles disappeared.

[ Problem Point ] It’s being checked by the tester just after the production of electronic components. Control of the heat cycle was difficult. [ ⇒Kaizen Point ] Aging was done with a wide nozzle of the Air Blow Heater. ...

[ Problem Point ] We were bagged and dried groceries. But there was trouble grows mold. [ ⇒Kaizen Point ] It dried heating nitrogen by the Air Blow Heater. Because nitrogen did not contain water vapor. It became the anti-mold ...

The temperature of the hot air from theAir Blow Heater is T [℃], the gas flow rate is F [L / min.], And the power consumption of the Air Blow Heater is P [w]. Please be sure to double the ...

[ Problem Point ] Resin insulating coating was being used,so control of the dry temperature was difficult. [ ⇒Kaizen Point ] It dried spotting heating by the Air Blow Heater. The quality of the product has improved in the accurate ...

The withstand voltage of the Air Blow Heater is 0.3MPa for the H series and 0.4MPa for the S series. We can also manufacture the Air Blow Heater with higher withstand voltage by custom specifications. The discharge pressure displayed by ...

[ Problem Point ] Resin insulating coating was being used,so control of the dry temperature was difficult. [ ⇒Kaizen Point ] It dried spotting heating by the Air Blow Heater. The quality of the product has improved in the accurate ...

[ Problem Point ] We are looking for not emit gases high temperature heater. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater. It does not emit gases, it can accurate analysis. The idling time vanished, the current spending ...

[ Problem Point ] Heat ran away from the furnace,was the problem of quenching quality. [ ⇒Kaizen Point ] The furnace was air sealed with the Air Blow Heater. The temperature of the interior was kept,and the quality of quenching ...

[ Problem Point ] We have no way to powerful irradiated lamp with infrared and ultraviolet. [ ⇒Kaizen Point ] Irradiated infrared by the Halogen Line Heater. Also UV lamp, the same type of custom-made ones. Since the maximum temperature ...

Since the lifespan of the Air Blow Heater varies depending on the usage conditions and is determined by multiple factors, it is very difficult to estimate the lifespan, and we do not guarantee the lifespan. Multiple factors include the lifespan ...

Please sure to use the Air Blow Heater with a rated voltage or less. Before applying the voltage, make sure that the gas is properly blown out from the hot air outlet. If the supply of compressed gas is stopped ...

[ Problem Point ] Laboratory has been electrified,the gas was not able to be used and I was in trouble. [ ⇒Kaizen Point ] It was heated by the Air Blow Heater. It was very useful for high temperature heating ...

[ Problem Point ] We have no way to heated uniformly long area. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater. Since the maximum temperature heated up in 5sec,immediately after the start of operation could work. Non-contact heating ...

[ Problem Point ] It was dry by steam. When winter came,we were in trouble because it condensed into dew. [ ⇒Kaizen Point ] Heated and dried in the Air Blow Heater. The dewfall disappeared because it used dry air.

[ Problem Point ] We have no idea about high temperature heater on short time. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater. Since the maximum temperature heated up in 5sec, immediately after the start of operation could ...

[ Problem Point ] The control of the surface tension of a metallic film was difficult when drying with the high temperature gas. [ ⇒Kaizen Point ] It dried using a wide nozzle by the Air Blow Heater. The surface ...

[ Problem Point ] We have no idea how to heat semiconductor wafer in the vacuum chamber. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater. Since the maximum temperature heated up in 5sec, immediately after the start of ...

[ Problem Point ] It’ll be done only to heat a culture medium from the surface. It couldn’t be heated uniformly and in trouble. [ ⇒Kaizen Point ] The heating air was made with the Air Blow Heater. The accuracy ...

[ Problem Point ] We have no idea how to deposition of aluminum in the vacuum chamber. [ ⇒Kaizen Point ] Heated by the Halogen Line Heater. Since the maximum temperature heated up in 5sec, immediately after the start of ...

[ Problem Point ] It was troubled to be contaminated with airborne bacteria breeding in the liquid directly in the aeration air. [ ⇒Kaizen Point ] The aeration was done after heating was sterilized by the Air Blow Heater. Airborne ...