[ Problem Point ] One operator is doing transferring in a drain by himself, so it isn’t possible to see through until it’ll be fill up the drum. [ ⇒Kaizen Point ] Started using the DLC-100B  Bell type. So loud ...

Easy to Use! It only  put into the drum, and turn on the power! By the time of fullness, the bell and light, warning sending. For Water, Oil and so on AC200V-240V Multiple power. How to use. 1. DLC insert ...

[ Problem Point ] Temperature control was difficult because it was heating with warm water. [ ⇒Kaizen Point ]  The alloy heated by the Air Blow Heater. since it heated at an exact temperature of a unit once, reproducibility of ...

[ Problem Point ] Because the fuel is wet, we were in trouble without good source of ignition. [ ⇒Kaizen Point ]  Output the high temperature air blow in the Air Blow Heater, was heated and dried. Since fresh air ...

[ Problem Point ] When winter came, it was troubled without the waterdrop after car washing getting dry. [ ⇒Kaizen Point ] Drained and dried with the Air Blow Heater.

[ Problem Point ] Although the drier for industry was used for the robot, having attached it, broke down immediately and we were troubled. [ ⇒Kaizen Point ] The burr was melted with the Air Blow Heater. Since discharge temperature ...

[ Problem Point ] There was no good thing can be transparent while keeping the high-temperature heating the glass tube. [ ⇒Kaizen Point ] Were tested while raising the temperature up to 1000 ℃ in the Air Blow Heater Accuracy ...

[ Problem Point ] The wire did not fit, it was troubled by the temperature near the freezing point of winter. [ ⇒Kaizen Point ] It warmed by the Super Infrared Heater of temperature up at the moment. The wire ...

[ Problem Point ] The performance of the battery did not come out but it was troubled by the temperature near the freezing point of winter. [ ⇒Kaizen Point ] It warmed by the Super Infrared Heater of temperature up ...

[ Problem Point ] There was omitted thermal diffusion test by air. [ ⇒Kaizen Point ] The diffusion test was done,the amount control of winds in increments of 1liter unit raising temperature in increments of 1 degree unit with a ...

[ Problem Point ] The marks of water drop remained and were worrisome when natural drying was carried out. [ ⇒Kaizen Point ] Nitrogen was heated with the Air Blow Heater and it dried. The marks of water drop were ...

[ Problem Point ] When processing the wire produced by powder metallurgy,it had trouble to cracking or cutting. [ ⇒Kaizen Point ] So brittle,while heating to the processing 400 ℃ – 700 ℃ by the Air Blow Heater. The quality ...

[ Problem Point ] It wasn’t possible to make hot argon gas while keeping the purity. [ ⇒Kaizen Point ] Argon gas was heated by the Air Blow Heater. Air did not mix and the high temperature gas of 550℃ ...

[ Problem Point ] We have no idea about how to no-contact heating in line. [ ⇒Kaizen Point ] The high temperature air of the suitable temperature was made with the Air Blow Hater and it projected. It came to ...

[ Problem Point ] We have no idea about how to heating and cooling at the same time in line. [ ⇒Kaizen Point ] It made high fever air of a suitable temperature with the Air Blow Heater, projected and ...

[ Problem Point ] It was in trouble because the temperature of steam of the tunnel type steam-oven was not able to be adjusted. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to ...

[ Problem Point ] It was in trouble because the heat resistant of the polyethylene is low. [ ⇒Kaizen Point ] The temperature of air of the heating sterilization furnace has been adjusted with the Air Blow Heater. Possible to ...

[ Problem Point ] There was distance from a boiler,it was in trouble because the temperature of the steam fell. [ ⇒Kaizen Point ] Steam has overheated with the Air Blow Heater. It is possible to make overheating saturated steam ...

[ Problem Point ] It was in trouble because the priority oxidation of the tin occurred. [ ⇒Kaizen Point ] The soldering iron shielded with the nitrogen gas was made. The priority oxidation of tin is suppressed to solder in ...

[ Problem Point ] It was in trouble because the surface of the tart burned. [ ⇒Kaizen Point ] The surface was warmed over by the Air Blow Heater. The temperature was able to be adjusted, the combustion color was ...