[ Problem Point ] We could not roast uniformly at the optimum temperature up to now. [ ⇒Kaizen Point ] We roasted with Air blow Heaters. Delicate temperature control around 180℃ can be easily done in 1℃ increments. Moreover, since ...
Read More »No.108 Hot air roasting of Almond nuts
[ Problem Point ] We could not roast uniformly at the optimum temperature up to now. [ ⇒Kaizen Point ] We roasted with Air blow Heaters. Delicate temperature control around 150℃ can be easily done in 1℃ increments. Moreover, since ...
Read More »No.107 Hot air roasting of Cacao beans
[ Problem Point ] We could not roast uniformly at the optimum temperature up to now. [ ⇒Kaizen Point ] We roasted with Air blow Heaters. Delicate temperature control around from light roasting 120℃ to dark roasting 160℃, can be ...
Read More »No.106 Hot air roasting of Coffee beans
[ Problem Point ] We could not roast uniformly at the optimum temperature up to now. [ ⇒Kaizen Point ] We roasted with Air blow Heaters. Delicate temperature control of roasting at 180℃ for the first time and roast at ...
Read More »No.105 Shrink fitting of a small cylinder
[ Problem Point ] Heating equipment that can be used in online was necessary. [ ⇒Kaizen Point ] We ware shrink-fitted by using the Air Blow Heater. The start of the line become faster. Installation because it does not use ...
Read More »No.104 Examination of a engine turbine
[ Problem Point ] Heating equipment of a lean air was needed. [ ⇒Kaizen Point ] Heating the turbine using the Air Blow Heater. Lean air in proportion to the law of Charles was obtained.
Read More »No.103 Molding of a polyethylene container
[ Problem Point ] The reduction of the defectiveness rate was necessary. [ ⇒Kaizen Point ] We ware molded using the Air Blow Heater. Since the heating air fluidity of the resin is improved.
Read More »No.102 Drying after the leak test using a water tank
[ Problem Point ] Shortening of the dry time was necessary. [ ⇒Kaizen Point ] We ware heated to work by using the Air Blow Heater. Dry time became short more markedly than air blow drying. Installation because it does ...
Read More »No.101 Adhesion of PVC sheet
[ Problem Point ] The exact temperature control was necessary. [ ⇒Kaizen Point ] We adhered to PVC sheet using the Air Blow Heater. Rise early, it has allowed accurate temperature control. Besides, it became the maintenance-free as Air Blow ...
Read More »Power Cable for Heater Controller
Manufacture the specification of the power cable. When the plug or the connector which the upper figure does not have are necessary, we will manufacture as much as possible. << Quotation model specification method >> (Heater controller model) – (Plug ...
Read More »Cubic Test Stand
[ CTS-L & CTS-M ] [ CTS-M + HLH-65W ] * Refractory brick, Manual lifting table and Heat resistant plate are optional. [ CTS-M + HPH-160 ] * Refractory brick, Manual lifting table and Heat resistant plate are optional.
Read More »Basic knowledge of Resin heating 3.The kind of resin -11 Paint
1.About Paint The paint is a material to apply on the surface protect an object and dressed richly or to give an original function. The history of the paint represented for a long time by lacquering is in Japan, but ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -10 Conductive resin
There is a substance that can flow electricity, that can not flow electricity. Flow electricity substance is “Conductor”, can not flow electricity substance is “Insulator”, Silicon(Si) and Germanium (Ga) of the middle is the “Semiconductor”. Metal is a conductor was ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -9 Light curing resin
1. About light curing Light is a collection of particles called photons, but the individual photons have the nature of the electromagnetic wave. Photon will have a unique energy, the same way as the electromagnetic waves and gather, is proportional ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -8 Liquid resin
About liquid resin The liquid resin is a resin that exists as a liquid at room temperature. In ISO 554-1976 has defined as a range of 20 ℃ ± 15 ℃ (5 ~ 35 ℃) “cold”. The temperature at which ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -7 The liquid crystal
What is the Liquid Crystal? The liquid crystal is a substance that is an intermediate state or such conditions, liquid and solid (crystalline). At present, those that express the liquid crystal structure is not found in other than the resin. ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -6 Elastomers
Elastomer The elastomer is the generic name of industrial materials having rubber elasticity. It was first used from 1960 early in the shortened form of the elastic polymer (polymer resilient). In general, a synthetic rubber from natural rubber or old, ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -5 Super engineering plastics
Super engineering plastics (hereinafter abbreviated SEP) is a reinforced resin of engineering plastic function. In part it is also referred to as a “Special engineering plastics.” SEP is a highly heat-resistant third generation synthetic resin with improved intrinsic properties of ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -4 Engineering plastics
Name of engineer plastics, DuPont was the first time used in the PR of the product name of the polyacetal resin “Delrin” in 1959. Since this resin is used in mechanical parts such as gears, it was given the designation ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -3 Thermoplastic resin
Thermoplastic resin is a solid polymer of one-dimensional structure (a set of polymer of linear structure), it is melted on heating and cooling will be solid. Even the glass-transition temperature or the melting point is softened by heating, it is ...
Read More »No.100 Differential temperature inspection of the heat pipe
[ Problem Point ] Good operability heating equipment was needed. [ ⇒Kaizen Point ] We ware heated heat pipe using the Air Blow Heater. It became possible to have multi-point measurement that could not until now. Moreover, since the non-contact ...
Read More »Basic knowledge of Resin heating 3.The kind of resin -2 Thermosetting resin
Thermosetting resin is a polymer material, which is also referred to as a thermosetting plastic.Raw material was fluidized by heating and pressing, it becomes the product shape.With that configuration to the bound of the monomer with a three-dimensional network structure, ...
Read More »No.99 Culture of anaerobic microorganisms
[ Problem Point ] It could not be freely temperature change Dummy-gas. [ ⇒Kaizen Point ] We use the Air Blow Heater DGH series for environmental, We made dummy gas change the temperature freely, and a cultivation test of an ...
Read More »No.98 Drying of the adhesive seal
[ Problem Point ] Shortening of tact time of the adhesive sealing process has been required. [ ⇒Kaizen Point ] We dried seal by the Air Blow Heater. It is the drying time is shortened by a double effect of ...
Read More »Basic knowledge of Resin heating 3.The kind of resin-1 The type of bond and molecular
Atoms will assemble and be a molecule. Between the molecules and molecular force called “intermolecular force” is working, and then solidified (crystallization). The chemical bond atom is a like to win the closed-shell structure in search of stable reaction, from ...
Read More »