[Basic structure of the Halogen Point Heater] It consists of a Condensing mirror and a lamp base and a cooling unit. The material of the lamp base is Aluminium. The lamp uses quartz glass and is fixed to the base ...
Read More »No.97 Temperature performance evaluation test of the rechargeable battery
[ Problem Point ] The advanced battery with environment resistance is required for. [ ⇒Kaizen Point ] The temperature test was done using the Air Blow Heater. The rapid temperature change which was impossible until now has been reproduced. The ...
Read More »4-2.Drying speed and wind speed of the hot air
Temperature and Humidity of the hot air is called the steady-state drying conditions drying constant. 4-2-1.If wind velocity of a hot wind is enlarged, a coefficient of heat transfer will also become large. Heat transfer coefficient of the dry conditions ...
Read More »No.22 High-temperature sterilization of Supatera
[ Problem Point ] The small high temperature sterilization equipment not using an open flame was required. [ ⇒Kaizen Point ] It is using a Halogen Point Heater that can be sterilized in 5 seconds after lighting. Sterilization process without ...
Read More »Heat shrink film of battery
*Check Video is here This video is a demonstration in the air of 400 ℃ Heat shrink film of battery by the Air Blow Heater.
Read More »2-1.Overview of the Halogen Point Heater
Halogen Point Heaters convert the electricity of halogen lamps into light, A heater that uses a Condensing mirror to concentrate the light in dots and circles and heat it at a high temperature. ◎ Since it heats directly without a ...
Read More »Evaporation of water
*Check Video is here This video is a demonstration which evaporates 6.5 cc of tap water with 500℃ air by the Air Blow Heater.
Read More »4-1.The air and the nitrogen
Check the performance of the air and nitrogen as the medium to be used in the hot-air drying. 4-1-1.The role of air Air at room temperature, the atmospheric pressure will behave as a nearly ideal gas. Density of air ρ ...
Read More »Make a hole in the Polyolefin heat-resistant five-layer film
*Check Video is here This video is a demonstration drill holes in the air of 400 ℃ in Polyolefin heat-resistant five-layer film in the Air Blow Heater.
Read More »Make a hole in the polystyrene PS pack
*Check Video is here This video is a demonstration drill holes in the air of 400 ℃ in polystyrene PS pack in the Air Blow Heater.
Read More »3-9.The 6 Fundamental law and the 4 thermodynamic law about drying.
The 0th law of thermodynamics—Law of heat balances James Clerk Maxwell FRS FRSE (13 June 1831 – 5 November 1879) Scottish mathematical physicist. If the objects A and B, B and C are thermal balances, A and C are also ...
Read More »No.96 Heating of the shielding gas of laser welding
[ Problem Point ] Oxide film on the weld surface is worried about. [ ⇒Kaizen Point ] High temperature heating of the shielding gas was carried out using the hot wind heater. Even if it thickened metal, welding said well.
Read More »No.95 Hot air shot peening
[ Problem Point ] In order to thicken a metallic thin film, the high temperature hot wind was required. [ ⇒Kaizen Point ] The shot-peened under high temperature conditions using the Air Blow Heater. Junction went well even if thickening ...
Read More »1-4.Precautions for Using Halogen Heaters
Measures against inrush current of halogen heater The electrical resistance of the halogen heater when it is off is 0.2 ~ 0.7Ω. In other words, it is easy for a large inrush current to flow momentarily when it is lit. ...
Read More »Make a hole in the polypropylene PP tray
*Check Video is here This video is a demonstration drill holes in the air of 400 ℃ in polypropylene PP tray in the Air Blow Heater.
Read More »No.94 Hot air anthelmintic
[ Problem Point ] Requires secure chemical-free pest control that do not use chemical fumigation. [ ⇒Kaizen Point ] Hot air is anthelmintic, in a way that does not use chemicals, to disinfect from egg to adult in a hot-air, ...
Read More »3-8.Three types of drying 3.Drying of the paint film and Membrane
To say that “drying”, there is a dry work of three types. They are dryness of surface water of adhesion, dryness of a coat, and internal dryness of material. Since internal dryness has been explained until now, describes the drying ...
Read More »No.93 Heat shrink the capacitor
[ Problem Point ] It did not shrink processed while temperature control. [ ⇒Kaizen Point ] The precise temperature control in the Air Blow heater, it was appropriate temperature heating. Thermal destruction is eliminated, defect rate was reduced.
Read More »No.92 Temperature setting of the coil spring testing machine (low-temperature material)
[ Problem Point ] There was no evaluate the performance while changing the temperature of the coil springs. [ ⇒Kaizen Point ] It heated from room temperature to 850℃ with the Air blow heater. The quality assessment in the arbitrary ...
Read More »1-3.How to Select Point Heater and Line Heater
The difference between a Halogen Point Heater and a Halogen Line Heater are whether it heats a point and circle or a line or plane. For point heating or circular heating in millimetres, use a “Halogen Point Heater ...
Read More »No.91 Temperature setting of the tensile testing machine (low-temperature material)
[ Problem Point ] There was no evaluate the performance while changing the temperature of the test piece. [ ⇒Kaizen Point ] It heated from room temperature to 850℃ with the Air blow heater. The quality assessment in the arbitrary ...
Read More »3-7.Three types of drying 2.Drying of the surface attached water
Even if it tells “dryness” to a mouthful, there are three kinds of dry work. They are dryness of surface water of adhesion, dryness of the coating film, and internal dryness of material. Since the preceding sections has explained the ...
Read More »No.90 Heat test of bearing
[ Problem Point ] Managing the heat-resistant temperature of grease, it came to carry out a quality assessment and there was nothing. [ ⇒Kaizen Point ] It heated from room temperature to 550℃ with the Air blow heater. The quality ...
Read More »1-2.Features of Halogen Heaters
A halogen heater is a heater that converts the supplied electricity into light rays by a halogen lamp, concentrates the light with a condensing mirror, and heats it at a high temperature. Most of the wavelength distribution of halogen lamps ...
Read More »3-6.Importance of dehydration
Energy for evaporating the water 1kg of 20 ℃ is 2454kJ. 1kW/h is 3600kJ so…. 2454kJ is the working time and energy consumption of the same amount running 40 minutes of 1kW motor. Or, the halogen heater 5kw 85% efficiency ...
Read More »