Air Blow Heater

 *Check Video is here This video is Bending of thin PET sheet using Air Blow Heater. Please check the following site for more information.

 *Check Video is here This video is a Heat-hardening of refractory putty by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

 *Check Video is here This video is a heat curing of special polyurethane adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

 *Check Video is here This video is a heat curing of special modified silicone polymer adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

 *Check Video is here This video is a heat curing of styrene-butadiene rubber adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

1.Feature of the High temperatur medium size Air Blow Heater ABH-HR ABH-HR can heat passage gas to 1050℃ ABH-HR can heat gas in an environment of 200 ° C ABH-HR can discharge high temperature air up to 1000 ℃. ABH-HR ...

*Check Video is here This video is a heat curing of vinyl acetate adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

*Check Video is here This video is a heat curing of chlorobrene rubber adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

*Check Video is here This video is a dry curing of epoxy adhesive by the Air Blow Heater and the Halogen Point Heater. Please check the following site for more information.

SSR is a solid state relay made of semiconductor. ■ Features of mechanical relay ① Voltage output and voltage output can be controlled simultaneously. ② Both current and voltage can be controlled simultaneously with current output. ③ AC output and ...

■ Function The heater burnout alarm function uses a dedicated current detector to detect the load current, and if the control output is lower than the current value set at ON, it is determined that the heater is burnt out ...

The communication function of the temperature controller and indicator controller has been gradually increased and enhanced. ① The simplest signal is the ON-OFF signal. The normal value or abnormal value can be output to the higher order by “ON-OFF” signal. ...

■ What is heat/cool control? For example, when conducting a performance evaluation test for electronic equipment, it is necessary to control the heater and cooling mechanism simultaneously. Heating / cooling control refers to a method in which one controller operates ...

In order to perform good control with a PID controller, it is necessary to set an appropriate PID constant according to the control target. Adjusting the PID constants is called “tuning”. When analog controllers were at their peak, operators tuned ...

PID operation is common for temperature controllers and indicating controllers. There is no difference in cost when using this in PI operation or in P operation alone. Then it seems like using PID control, which should get the best control ...

■ PID features It nned to eliminate the offset and make the control response faster. Use PID behavior to satisfy both. The basics PID control 1) Proportional action ( P action) that outputs a correction amount proportional to the current ...

Differential (PD) control is used to improve control response. Unlike the integral control, the derivative control has no control ability by itself. Used in conjunction with proportional control as proportional differential control. Differential control uses the rate of change of ...

It is thought that it can be controlled well by proportional control, but in reality, there is a problem when the current value approaches the set value. That is, the amount of operation becomes too small, and it becomes impossible ...

Proportional control is divided into three types, time proportional control, continuous proportional control, and position proportional control, depending on the heating method. ①Time proportional control (switching control) ◎ Time proportional control is a control that finely changes the ratio of ...

In the ON-OFF control, when the heating output (operating amount) is 0% or 100%, the control result overshoots due to the effect of detection and reaction delay, and cycling is repeated. Cycling is inevitable with ON-OFF control because it performs ...

If it is turned ON and OFF at one point, the output will be chattered and will be more susceptible to noise. For this reason, as shown in the figure, heating control usually has a range of ON-OFF, such as ...

If the current temperature is lower than the set value, turn on the heater to heat. When it becomes higher than the set value, turn off the heater and cool naturally. The control method that keeps the temperature constant by ...

Control Control is derived from the Latin contrarotulare, where contra means “to” and rotarye means “scroll”. When these are combined, the control comes from the fact that “if there is a difference, it will be corrected according to the authority ...

Daniel Rutherford Nitrogen keeps gas up to -195.8℃. Liquid up to -210℃. If it exceeds -210℃, it becomes ice and solidifies. It is often used as an inexpensive coolant. Liquid nitrogen is often used as a coolant, but also as ...

Cooling things with water has been practiced since ancient times. With direct cooling of cooling watermelon with well water, There is indirect cooling that water is injected and cooled by heat of vaporization. We use both for fire fighting. Such ...